[Pro Version] KIWI design VR Cable Management, 6 Packs VR Pulley System fits Quest/Rift S/Valve Index/HTC Vive/Vive Pro/HP Reverb G2/PSVR/PS VR2 VR Accessories, Compatible with Quest 2 Link Cable

Right out of the box I stretched out a pulley to test how silent it was. The claim of silence seems to mostly be based on the rubber that deadens the retraction click and this works well enough to be silent within vr even if not outside of it. That said, I immediately doubted the product after stretching it out further. The reason for deducting two stars is due to the tension ramping up as the cord is pulled out. The only adjustment is to change the slack but, without a corresponding adjustment to tension, this feature is nearly pointless. The recommended triangle setup really does work flawlessly for standing play but the pull becomes too noticeable after 1 or 2 steps in any direction. My space measures 3 meters by 3.5 meters according to the steam vr room setup so 1 or 2 steps is not sufficient. I spent a couple hours experimenting and here is what works best for my setup. First off, 6 pulleys is not enough so I ditched the triangle setup. Im very glad that more adhesive hooks were included than needed. I still have 3 points of contact with the ceiling but ended up chaining the pulleys together. 1st point nearest the pc has 1, 2nd point has 2, 3rd point has 3. I found that the easiest way to calibrate this was to place the headset into the corner. Each link of the chain could then be inspected and the rubber gripper on the cord adjusted until all pulleys were about the same length. A balance must be struck between ensuring that no pulley is stretched too far yet without the cord dangling low enough to entangle your neck or hands. Overall, this setup is decent but Im probably going to need to order a second kit. There just are not enough points of contact with the ceiling to keep the cord high enough. Ill likely have leftovers but I figure the rest can be spares. This would be a 5 star product if there was a way to adjust tension. This would be a 4 star product if they were more open about the requirements for a full room setup and sold a 10 pack going for about 1.5 the cost.

Keeps my cable off the floor and helps with mobility. One of the sticky pads came off the ceiling early on but I pressed it back on harder on a slightly flatter spot and so far all of them have stayed up for several months. If I had a more permanent VR space I would drill them in but these sticky pads are good enough for now.

Makes every game so much more fun on pc I hate the cord dangle on my back or the triping Hazzard or getting tangled but this system is clean strudy and fixings all my issues with pcvr and love it dont hesitate if you have the cash to spare get it you will not regret it.

I was skeptical buying this. I figured it was a gimmick but it makes a night and day difference with our Valve Index. The immersion is so much better without the cords hanging on you. It is not restrictive at all! Id buy it again.

I needed the sticky hooks because I didnt want holes in my apartment ceiling. The adhesion is great, but as soon as you stick it on, its not coming off. Good luck if you need to readjust them. I knocked off a star because itll rip off paint regardless of how slow and careful you are.

I think Ive said this about all the Kiwi products Ive purchased.. GAME CHANGER. Silent operation, At least 7 feet of pull with minimal resistance until you get to the last 2 feet. You know when youre about to run out of slack, but it doesnt interfere with the game. I can tell these people have played a lot of VR and know what is needed.

If you want to keep wires off of you and out of the way i would recommend picking these up. DO NOTE THE ADHESIVE IS VERY STRONG LIKE PEEL YOUR CEILING OFF IF NOT CAREFUL STRONG! I would recommend finding some other way of hanging these from your ceiling unless you want a more permanent set up. But overall great deal and a fantastic help for cable management with VR.

This pulley system was an affordable way to get the 16’ USB cable out of the way when playing VR. I’ve had the system for ~6 months and it’s held up well to my 12yr son’s Gorilla Tag and other, active VR games as he moves all over his room without any worry about yanking the cord out of the computer or the headset. Simple installation. You just twist a few screws into your ceiling to guide the wire and you’re done.

Before this purchase, I was using the pull-strings system for badges. DONT DO THAT! Itll be a waste of money. 150%, buy these instead. ID card string system, 24. This system, ~68. This is quieter, less tension, and the soft rubber fastener makes setting up the cable a breeze. If you have an overhead VR system, dont go cheap DIY like I did. This system is worth the price.

This is an amazing and cheap product. Ive messed around with wireless adapters but theres always issues with heavy batteries, disconnects, extreme expense, etc. This product is amazing though. It only took me about 5 minutes to set up and after playing with the length of the cable, I can barely feel any sort of tug unless I get right to the edge of my play area. Flat ceilings work best but theres a solution for popcorn ceilings as well. Theres no way I can go back or even consider a $300 adapter after trying this.