[Pro Version] KIWI design VR Cable Management, 6 Packs VR Pulley System fits Quest/Rift S/Valve Index/HTC Vive/Vive Pro/HP Reverb G2/PSVR/PS VR2 VR Accessories, Compatible with Quest 2 Link Cable

If you want to keep wires off of you and out of the way i would recommend picking these up. DO NOTE THE ADHESIVE IS VERY STRONG LIKE PEEL YOUR CEILING OFF IF NOT CAREFUL STRONG! I would recommend finding some other way of hanging these from your ceiling unless you want a more permanent set up. But overall great deal and a fantastic help for cable management with VR.

I love these for getting the cable out of the way when gaming. BUT there is one small issue. The tension is too tight and i feel too much resistance on the headset. This is particularly annoying for games that are immersive and require alot of crouching and dodging. I have not tried the triangle type setup yet just to be clear but I dont see it helping much. To the creators: I recommend that you add a tension adjustment like some competitors have. I bought these for the quality of design and would not have batted an eye to pay 10 or 15 more for that feature.

High quality product might be a little bit too sticky as if you have to move one due to misplacement it will rip the pain off the ceiling but dont have to worry about them coming off the ceiling while gaming

Took a flier on this product, to see if it would work with EV cable storage. Works great and better than I expected for that application. Needed to double up the last point where the plug of the EV charger was as the retract tension was a little to light to pull up the Plug end. Stores it nicely along the ceiling rather than lying on the floor.

Worked perfectly for cable management for my new Playstation psvr2. Easy to put up...used the screws instead of the adhesive pads. I first used command strips to make sure of my placement and a quick change out to a more permanent installation.

Right out of the box I stretched out a pulley to test how silent it was. The claim of silence seems to mostly be based on the rubber that deadens the retraction click and this works well enough to be silent within vr even if not outside of it. That said, I immediately doubted the product after stretching it out further. The reason for deducting two stars is due to the tension ramping up as the cord is pulled out. The only adjustment is to change the slack but, without a corresponding adjustment to tension, this feature is nearly pointless. The recommended triangle setup really does work flawlessly for standing play but the pull becomes too noticeable after 1 or 2 steps in any direction. My space measures 3 meters by 3.5 meters according to the steam vr room setup so 1 or 2 steps is not sufficient. I spent a couple hours experimenting and here is what works best for my setup. First off, 6 pulleys is not enough so I ditched the triangle setup. Im very glad that more adhesive hooks were included than needed. I still have 3 points of contact with the ceiling but ended up chaining the pulleys together. 1st point nearest the pc has 1, 2nd point has 2, 3rd point has 3. I found that the easiest way to calibrate this was to place the headset into the corner. Each link of the chain could then be inspected and the rubber gripper on the cord adjusted until all pulleys were about the same length. A balance must be struck between ensuring that no pulley is stretched too far yet without the cord dangling low enough to entangle your neck or hands. Overall, this setup is decent but Im probably going to need to order a second kit. There just are not enough points of contact with the ceiling to keep the cord high enough. Ill likely have leftovers but I figure the rest can be spares. This would be a 5 star product if there was a way to adjust tension. This would be a 4 star product if they were more open about the requirements for a full room setup and sold a 10 pack going for about 1.5 the cost.

This product works so well, comes with everything you would need to hook it up very easily and I cannot be happier. Works exactly how explained. Notice of quality. I haven’t used the sticky hooks because the screw in hooks don’t do to much damage to the ceiling and is easily fixed so I went for the stronger option. Once properly set up, that including proper cable management on headset and pulley system, I can’t even tell I’m hooked up to a cord.

I run the Vale Index, and I have a good size play area, with a padded floor. The wire for the valve is heavy, and, well, I can be a bit crazy with my movement. I box on thrill of the fight, and I engage Onward Daily, and aggressively. This means, I move, and need to move. These devices make that easy. I mean easy. They have sticky hooks, that stay on tight, with not one coming off in more than a month now of daily use. But, when I go to move them, they come off easy enough, and still...Yes...Still, stick right back on in the new location. I have moved them three times. I know...I know...unbelievable. But its true. Now, I started with a square pattern to hold my wires. Yes, I get it now, not the right pattern. A straight line is perhaps best, so, I got wise, and set them up better. World of difference. I will get another set soon, and improve, though the improvement is not needed. One set was enough, and I am glad I got this product right away. Price, forgetaboutit! Its perfect. No reason to not get your wires organized and I do not see a reason to shop around for other options, this works great. Thank you for the care.

These are great. Keeps the cable off the ground and more out of the way. Only way they could be any better is if they were just a little weaker cause it does pull a little more on the cable than I would like, but honestly is probably still less wear than me stepping on or tripping over it. Oh I used the hooks so I don’t know how well those will work but the anchors and hooks hold well.

I havent installed it yet, but the quality and design looks to be very good, just one small issue is it didnt include the ring hook. Im sure I can come up with a work around, but just thought to put that out there.